suedetree71

Fiat 500 Replacement Key Fob It could be time to replace the battery if your 500 remote key fob is not working. If you do replace the battery and it doesn't work then the issue is probably elsewhere. United Locksmith specializes in the creation of new keys for classic automobiles. We have all of the tools and accessories needed to provide this service. Dead Coin Battery The most common reason your Fiat 500 key fob will not lock or unlock the doors is a dead battery. The key fob comes with an in-built battery that can quickly deplete when it isn't being used often enough. If your remote starts to show signs of a loss in range or stopped working or not responding, then the battery could be dead. The battery in the key fob is held in place with metal retaining clips. If the clips are not secure, they could cause problems with contact that can prevent your remote to receive power. Utilizing a small screwdriver, break the retaining clip to remove the battery and then insert a fresh one. Be sure to use an identical replacement battery kind of voltage, the same size and specifications as the original battery. The key fob might be damaged or corroded by exposure to water. Even a brief bath in soapy water could cause damage to the electronic chip inside. It's best to keep your key fob in a dry environment. Water Damage Damage to your water supply could be the reason for your key fob's inability to function properly. The rubber seals on key fobs keep them from getting damaged by a slight splash or drizzle of water. However, it is crucial to keep the keys from the washing machine, the ocean, and even the pool. fiat 500 replacement key has an electronic chip which sends a message to the immobilizer system of your vehicle. The chip is what allows the 500 to lock and start. If it gets wet, however it will cease to function. If you want to check if your key fob is still functioning it is possible to clean the internal electronics with isopropyl or electronic cleaner. It is recommended to replace a key fob if it's submerged in salt water instead of trying to repair it yourself. A replacement fob could cost you some money, but it's a lot less expensive than paying to have your Fiat 500 towed to a dealership and fixed there! You can also make it yourself by following some simple steps. Make sure you have the right battery type before you attempt to open your key fob. You can find step-bystep instructions for any car keyfob on the internet. Faulty Chip The chip in the key fob is in direct communication with the immobiliser on your car to ensure that your vehicle will only start when the proper keys are inserted. If the chip is damaged or destroyed the car won't start, no matter what you do. Water damage or a dead cell phone battery are among the most common causes of an unreliable chip. It is best to delegate the job to a professional locksmith, who will be able to replace the chip quickly and at reasonable cost. If your key fob does not function after being exposed to clean water from a tap or rain take it off the battery. Wipe down the electronic component with paper towels. If the key fob will not function, there is an opportunity that it is a fried component and needs to be replaced. Some people will visit their dealer when they require an entirely new Fiat fob. However, this can be an expensive option. If you are seeking a cost-effective solution to have your Fiat key fob fixed Look no further than United Locksmith. We have the equipment and know-how to repair your Fiat fob in a timely and professional way. Faulty Receiver Module Fiat key fobs transmit an electrical signal to the vehicle that will unlock and close doors (and start the car if it has an automatic transmission) up to 50 feet. There are a variety of reasons why a fob could stop working. These include a dead coin battery or water damage buttons, worn ones as well as a receiver module problem or signal interference, or an electronic chip that has failed. If the fob was located in the pocket of someone who has suffered severe trauma (such as being dropped on the floor or washed in the washing machine) the fob may not be able to communicate with the Body Control Module (BCM) of the vehicle. This is because the BCM is secured and will only accept a signal from a genuine key, and not from any other. If this is the case, then you have to replace your fob. A professional locksmith will handle the entire process of replacing your key including programming a new key to your 500. They can even provide you with a clone fob that works exactly the same way as the original (and costs just a fraction of what it would cost).